Ammunition & Hazardous-Material Container RFID
RFID Ammo Can Tag
Military Ammunition Container ID
Quick answer
RFID ammo can tags put a MIL-STD-129R / MIL-STD-1168D DODIC + LOT identifier on PA70 / M2A1 / PA108 ammo cans, readable at 3-5 m. The GIAI-96 payload adds UN hazard class / division, compatibility group and NEW for DOT 49 CFR §173.62 Class 1 Explosives transport. MIL-STD-810H-qualified on-metal hardware survives -40 °C to +85 °C, and DoD 5160.65-M surveillance cycles run as automated EPCIS events.
- MIL-STD-129R / MIL-STD-130N IUID-aligned per-container identifier on every PA70 / PA108 / PA120 / M2A1 / M2A2 / M19A1 ammo can and 40 mm / 155 mm pallet — encodes DODIC + NALC + LOT + PA-INTERIM + DoDAAC + hazard-class label per MIL-STD-129R §5 + MIL-STD-1168D + UN Recommendations on Transport of Dangerous Goods.
- Dock-door portal + handheld UHF architecture — wall-to-wall inventory of a 50,000-container ASP / MMAC / MCAAP depot via walk-by / drive-by reads; DoD 5160.65-M ammunition surveillance cycles and MIL-STD-129R §5.5 DODIC / lot reconciliation run as automated EPCIS events instead of paper issue slips.
- MIL-STD-810H-qualified, DOT 49 CFR §173.62-aware hardware — on-metal UHF survives -40 °C to +85 °C, MIL-STD-810H Methods 501 / 502 / 507 / 509 / 510 / 514 / 516 shock / vibration / sand / dust / salt-fog; Class 1 Div 2 / ATEX Zone 22 portal stack supported; no pyrotechnic / propellant-incompatibility risk when encoded in a secured cell off the explosive line.
Used in these industries
Deployments where this product is referenced on our industry landing pages.
At a glance
Use these short answers to decide whether this page matches the project before moving into the detail.
Chip options
Impinj Monza R6-P for baseline PA70 / M2A1 / M2A2 / M19A1 / PA108 / PA120 containers; Impinj M750 / M770 / M775 for 40 mm crate / 155 mm pallet long-range yard portal re...
Frequency / air interface
860-960 MHz UHF Gen2v2 per EPCglobal Class 1 Gen 2 v2.1 + ISO/IEC 18000-63:2015 for yard portal, dock-door, igloo and handheld reads; 13.56 MHz HF per ISO/IEC 14443-3 Ty...
Next step
Ready to move forward? Start your inquiry to get specific answers for this project.
Request quote and samples- Asset identifier scheme
-
MIL-STD-129R §5 military shipping label + MIL-STD-1168D DODIC / NALC / LOT assignment encoded as a GS1 GIAI-96 per GS1 Tag Data Standard 2.0 §7.1 carrying the full DODIC (4-character munition code) + NALC (2-character interim) + LOT serial + DoDAAC consignee / consignor + UN hazard class / division (1.1 / 1.2 / 1.3 / 1.4 / 1.5 / 1.6) + compatibility group (A-S) per DOT 49 CFR §173.52 + NEW (Net Explosive Weight) per 49 CFR §172.202 + hazard-division placard (ORM-D for small-arms, Class 1.4S) + ATF 27 CFR §555.109 marking of explosive materials + ITAR USML Category III export control flag + manufacturer CAGE code + date of pack per DoD 5160.65-M. Container events publish as EPCIS 2.0 ObjectEvents with bizStep=shipping / receiving / storing / issuing / demilitarizing and disposition keyed to DoD 5160.65-M surveillance state (serviceable / unserviceable-reparable / unserviceable-condemned).
- Form-factor SKUs (6)
-
(1) PA70 / M2A1 .50-cal can (100 × 50 mm on-metal tag screwed / riveted into spare stencil panel on lid or sidewall, Monza R6-P + UCODE 9); (2) PA108 / M2A2 / M19A1 larger can (100 × 50 mm + reinforced epoxy potted per MIL-DTL-24203 ammunition-box paint-system compatibility); (3) PA120 / PA125 modern fiber-reinforced plastic can (anti-metal not required — flexible UHF inlay bonded to lid); (4) 40 mm / 25 mm / 20 mm wooden crate / PA116 / PA117 (20 × 10 mm on-wood staple-mount inlay + QR-code fallback per MIL-STD-129R §5.8); (5) 155 mm / 105 mm projectile pallet (80 × 40 mm long-range M775 for 5-8 m portal read on palletized unitized loads per MIL-STD-1660); (6) SAAMI sporting-arms case / commercial cardboard outer (flexible UHF 50 × 25 mm on cardboard + adhesive backing; SAAMI Z299.1-5-aware encoding for commercial distribution including ATF 27 CFR §478.121 / NICS records).
- Housing material & surface qualification
-
Polycarbonate / polyurethane / ABS overmold rated to MIL-DTL-24203 CARC / CARC-compatible paint systems; MIL-STD-810H Method 501 / 502 (-40 °C to +85 °C); MIL-STD-810H Method 514 vibration including Procedure I truck / vehicle transport profile + Annex C ballistic transport; Method 516 shock 40g / 11 ms half-sine; Method 509 salt fog 96 h; Method 510 sand/dust; Method 507 humidity 10 cycles; ASTM B117 1,000 h for naval / maritime storage; MIL-STD-810H Method 520 combined environments for deployed operations; UL 94 V-0 flammability; MIL-DTL-55302 for connector / inlay when potted.
- Environmental & hazardous-area rating
-
IP67 / IP68; ATEX / IECEx Zone 21 / 22 dust-rated readers + tags for propellant-dust / small-arms-primer-dust operations; UL / CSA Class I Div 2 + Class II Div 1-2 for propellant / pyrotechnic atmospheres per NFPA 495 / NFPA 400; MIL-HDBK-1013 physical security of sensitive conventional arms; DoD 4145.26-M contractor's safety manual for ammunition / explosives compatibility verified per DESR 6055.09 Edition 1; NFPA 70 Art. 500 hazardous-classified-location wiring at the ASP portal; no intrinsic-safety rating needed on the passive RFID tag itself (zero active emissions).
- Read range
-
3-5 m walk-by / drive-by at the ASP / yard portal; 5-8 m palletized unitized load (155 mm / 105 mm) at a dock-door portal; 1-3 m handheld at individual-can inspection; 0-5 cm HF NFC tap for NTAG424 DNA per-container cryptographic chain-of-custody on ITAR-controlled USML Category III and ATF 27 CFR Part 555 explosive-material lots; igloo-interior read validated in dense-stacked configurations per MIL-STD-129R §5.4.
- DODIC / NALC / LOT cadence engine
-
Automated inventory reconciliation against MIL-STD-1168D DODIC / NALC / LOT tables; DoD 5160.65-M ammunition surveillance cycle triggers (quarterly / semi-annual / annual dependent on ammunition family); DoDM 4160.28 Defense Materiel Disposition for demilitarization; RCRA 40 CFR §266.202 military munitions rule for waste-military-munitions disposition; DOT 49 CFR §173.62 Table shipping-description generation; 49 CFR §172.202 NEW calculation at palletization; automatic ATF 27 CFR §555.127 records-of-transactions + §555.109 marking verification for law-enforcement / commercial explosives.
- Compliance framework
-
MIL-STD-129R Marking for Shipment and Storage · MIL-STD-130N Change 1 Identification Marking of U.S. Military Property · MIL-STD-1168D DODIC / NALC / LOT Ammunition Marking · MIL-STD-1660 Pallet / Unitized Load Standard · MIL-STD-810H · MIL-STD-461G · MIL-DTL-24203 (paint) · DoD 4145.26-M Contractor's Safety Manual for Ammunition and Explosives · DoD 5160.65-M Single Manager for Conventional Ammunition · DESR 6055.09 Edition 1 DoD Explosives Safety Standards · DoDM 4160.28 Defense Materiel Disposition · DoD Instruction 8320.04 IUID · AR 700-80 / AR 700-65 · NAVSEA OP 5 · AFMAN 91-201 · DOT 49 CFR Part 172 / §172.202 / Part 173 / §173.62 / §173.52 Class 1 Explosives + Compatibility Groups · 49 CFR Part 175 / 177 / 178 · DOT Special Permit DOT-SP program · ATF 27 CFR Part 555 Commerce in Explosives (§555.109 marking, §555.127 records of transactions) · 27 CFR Part 478 ATF FFL · 18 USC §922 / §923 · ITAR 22 CFR 120-130 USML Category III (ammunition) · EAR 15 CFR 730-774 · NATO STANAG 2493 Ammunition Marking · NATO STANAG 4439 Insensitive Munitions · NATO AASTP-1 Allied Ammunition Storage & Transport Publication · UN Recommendations on the Transport of Dangerous Goods (Model Regulations, Rev. 23) · UN Orange Book + ICAO TI + IATA DGR + IMDG Code · SAAMI Z299.1 / Z299.2 / Z299.3 / Z299.4 / Z299.5 · NFPA 400 · NFPA 495 · NFPA 484 · NFPA 498 · NFPA 70 Art. 500 · 40 CFR §266.202 military munitions rule · OSHA 29 CFR 1910.109 · ATEX 2014/34/EU · IECEx · FCC Part 15 · ETSI EN 302 208 · IC RSS-247 · GS1 TDS 2.0 + EPCIS 2.0 · NXP AN12196 NTAG424 DNA SUN CMAC AES-128.
- Platform integration
-
DoD logistics: Global Combat Support System-Army (GCSS-Army) / Logistics Information Warehouse (LIW) / Munitions History Program (MHP) / Total Ammunition Management Information System-Revised (TAMIS-R) / Standard Army Ammunition System-Modernization (SAAS-MOD); USMC Ordnance Information System-Marine Corps (OIS-MC); USAF Combat Ammunition System (CAS); USN Retail Ordnance Logistics Management System (ROLMS-I); DLA Defense Ammunition Center (DAC) feeds; DoD IUID Registry via PIEE / iRAPT. Federal law enforcement: ATF eForm 6 / eForm 5400.5 / Explosives Tracing Center, FBI Weapons of Mass Destruction Directorate (WMDD) / HAZMAT Response Unit; US Marshals / DEA / Secret Service armory and evidence systems. Commercial: SAAMI-aligned manufacturer ERPs (Olin / Vista Outdoor / Sig Sauer / Federal / Remington / Winchester); DOT Hazardous Materials Information System (HMIS) for transportation; carrier systems: USPS / FedEx / UPS HazMat; CHIEF / ACE customs + ITAR DTrade filings. EAM / WMS: Maximo + Maximo Aviation, SAP S/4HANA + EHS Management + GTS for export, Oracle WMS, Manhattan WMS, Körber / HighJump WMS, Infor EAM Public Sector. Surveillance: ammunition-surveillance lab feeds (lot-acceptance / service-test) per DoD 5160.65-M; AIT-III / RFID Tier-2 Enterprise Visibility Sensor Network for deployed operations.
- Serial & cryptographic provenance
-
Per-container DoD UID / GIAI-96 + DODIC / NALC / LOT encoded at Proud Tek secured encoding cell against DoD IUID Registry extract and MIL-STD-1168D DODIC/NALC/LOT table; encoding takes place off the explosive line in a separate bonded facility per DoD 4145.26-M compatibility rules; optional NTAG424 DNA SUN CMAC AES-128 key derivation per NXP AN12196 for ITAR-controlled USML Category III, ATF 27 CFR Part 555 explosive-material lots and NATO Tier-1 AASTP-1 programmes requiring per-scan signed events; key-management pack supports DCSA physical-security inspection, ATF compliance inspection, ITAR registration audit, and EU / UK dual-use export audit.
- MOQ
-
1,000 units per SKU for standard R6-P / UCODE 9 PA70 / M2A1 / M2A2 / PA108 / PA120 variants; 2,000 units for M775 long-range 155 mm / 105 mm pallet variants; 1,000 units for NTAG424 DNA cryptographic variants. Lead time 4-6 weeks for standard; 6-8 weeks for NTAG424 DNA + MIL-STD-1168D DODIC / NALC / LOT pre-encoding pack with manufacturer CAGE code + DoDAAC + hazard-class reconciled documentation trail.
- Typical pricing
-
USD 0.60–2.50 /pc by size (typical FOB Shenzhen range) — firm quote in one business day.
Commercial terms
- MOQ
- Varies by SKU — stock items from 100 pcs; custom production typically 200-1,000 pcs
- Lead time
- Production 2-3 weeks after artwork and encoding sign-off; reorders on a 3-4 week cycle
- Samples
- Free samples and RF test report with every order; courier at customer cost
- Payment
- 50% T/T deposit, 50% before shipment; Net 30/60 for established accounts; LC for large orders
- Shipping
- FOB Shenzhen / Yantian; DHL, FedEx or EMS air freight; sea LCL / FCL for volume
- Response
- Itemized quote within one business day, Mon-Fri (UTC+8)
Why paper DD Form 1348 / 1387-2 + stencil marking fails MIL-STD-129R + ATF + DOT audit
- MIL-STD-129R §5 military shipping label + MIL-STD-1168D DODIC / NALC / LOT marking requirements are routinely executed via stencil, paint-pen and paper DD Form 1348 / 1387-2. ASP / MMAC / MCAAP depots with 50,000+ containers cannot reconcile depot-paper state to SAAS-MOD / TAMIS-R / GCSS-Army / MHP in real time, producing surveillance-cycle gaps the DCSA ammunition-safety inspector regularly cites.
- DoD 5160.65-M single-manager-for-conventional-ammunition surveillance windows (quarterly / semi-annual / annual dependent on family) are tracked on paper ammunition-condition-code cards. Out-of-cycle lots slip to unserviceable-reparable before the condition-code review — a preventable-loss finding under DESR 6055.09.
- DOT 49 CFR §173.62 Class 1 Explosives + §172.202 NEW + §173.52 compatibility-group marking depends on stencil legibility in salt-fog / sand / desert storage. Weathered stencils drive carrier-refusal events, placard mismatches and HMIS citations during DOT roadside inspection.
- ATF 27 CFR Part 555 Commerce in Explosives (§555.109 marking, §555.127 records of transactions) and ATF Explosives Tracing Center requests turn into multi-hour paper-pull exercises at law-enforcement bomb-squad evidence stores, explosives distributors and SAAMI-aligned manufacturers.
- ITAR 22 CFR 120-130 USML Category III export-controlled lots require tight custody documentation. Paper chain-of-custody during contractor-to-DoD-to-coalition transfers cannot defend an ITAR audit or meet NATO STANAG 2493 marking / STANAG 4439 insensitive-munitions documentation.
How Proud Tek solves it — MIL-STD-129R / MIL-STD-1168D / DOT / ATF / ITAR / NATO-fit ammo-container RFID
Stencil / paint-pen + paper DD 1348 / 1387-2
- Stencil / paint-pen MIL-STD-129R marking — weathers in desert / salt-fog storage; DOT roadside placard-mismatch citations.
- Paper DD 1348 / 1387-2 + ammunition-condition-code cards — SAAS-MOD / TAMIS-R divergence; DoD 5160.65-M cycles slip.
- Manual §555.127 records of transactions + §555.109 marking — ATF Explosives Tracing Center requests take hours / days to satisfy.
- No cryptographic chain-of-custody — ITAR USML Cat. III and NATO STANAG 2493 audits defended on paper alone.
- No portal automation — container loss / pilferage undetected until next quarterly surveillance inventory.
Proud Tek MIL-STD-129R / 1168D / DOT / ATF / ITAR / NATO ammo-container RFID
- GIAI-96 carrying MIL-STD-129R + MIL-STD-1168D DODIC / NALC / LOT + UN hazard + compatibility group + NEW + DoDAAC — readable across paint / sand / salt-fog / CARC.
- EPCIS 2.0 event feed syncs SAAS-MOD / TAMIS-R / GCSS-Army / MHP in real time; DoD 5160.65-M cycle scheduler automatic.
- Auto-generated §555.127 / §555.109 records + ATF Explosives Tracing Center export; SAAMI commercial pack export on demand.
- NTAG424 DNA SUN CMAC AES-128 per-scan signature + Monza R6-P tamper flag — ITAR / STANAG 2493 / STANAG 4439 audits defensible.
- UHF yard / dock-door / igloo portal stack; MIL-STD-810H Class II Div 1-2 hardware; container-movement events logged in seconds.
- Per-container GS1 GIAI-96 carrying the full MIL-STD-129R shipping label + MIL-STD-1168D DODIC / NALC / LOT vector + UN hazard class / division + compatibility group + NEW + DoDAAC + CAGE. Encoding runs on Monza R6-P / M775 / UCODE 9 / Higgs-9 / NTAG424 DNA across PA70 / M2A1 / M2A2 / PA108 / PA120 / 40 mm crate / 155 mm pallet / SAAMI SKUs.
- Drive-by and walk-by yard + dock-door + igloo UHF portal stack — 50,000-container wall-to-wall inventory in hours instead of weeks. DoD 5160.65-M surveillance cycles run as automated EPCIS 2.0 events. RFID Tier-2 Enterprise Visibility Sensor Network compatible.
- MIL-STD-810H-qualified hardware survives CARC-paint compatibility, -40 °C to +85 °C, 96 h salt-fog, sand/dust, shock, vibration including Method 514 vehicle-transport + Annex C ballistic-transport profile. ATEX Zone 22 + Class II Div 1-2 portal stack handles propellant-dust environments. Tag encoding occurs in a bonded facility off the explosive line per DoD 4145.26-M.
- Wiring into SAAS-MOD / TAMIS-R / GCSS-Army / MHP / LIW / OIS-MC / CAS / ROLMS-I + DoD IUID Registry via PIEE / iRAPT. Feeds cover ATF eForm 6 + Explosives Tracing Center + FBI WMDD / HAZMAT, SAAMI-aligned manufacturer ERPs, DOT HMIS + carrier HazMat feeds, ITAR DTrade + CHIEF / ACE customs, and NATO AASTP-1 / STANAG 2493 export for coalition operations.
- NTAG424 DNA SUN CMAC AES-128 per-scan signature for ITAR USML Category III + ATF 27 CFR Part 555 + NATO STANAG 2493 Tier-1 lots. Monza R6-P tamper flag closes the container-swap / cloning attack surface and produces evidentiary records the DCSA / ATF / DOT / ITAR audits expect.
Operating notes drawn from ammunition-container traceability programmes
- Weeks 1-3
SAAS-MOD / TAMIS-R / MHP / OIS-MC / CAS / ROLMS-I extract + MIL-STD-1168D DODIC / NALC / LOT reconciliation; DoDAAC + CAGE + UN hazard + compatibility-group inventory; GS1 GIAI-96 issuer-code registration per GS1 TDS 2.0; encoding-facility designation off the explosive line per DoD 4145.26-M + DESR 6055.09.
- Weeks 4-6
SKU + chip selection (Monza R6-P / M775 / UCODE 9 / Higgs-9 / NTAG424 DNA); PA70 / M2A1 / M2A2 / PA108 / PA120 / 40 mm crate / 155 mm pallet / SAAMI case placement; MIL-STD-810H Method 501 / 502 / 507 / 509 / 510 / 514 / 516 validation on pilot lot including Method 514 Procedure I + Annex C ballistic-transport profile; ATEX Zone 22 + Class II Div 1-2 portal reader validation per NFPA 495 + NFPA 484.
- Weeks 7-12
Pilot ASP + MMAC / MCAAP production line + contractor bonded-warehouse + SAAMI commercial distributor rollout; yard + dock-door + igloo portal wiring; DoD IUID Registry sync via PIEE / iRAPT + SAAS-MOD / TAMIS-R / MHP / OIS-MC / CAS / ROLMS-I feed dry-run; ATF eForm + Explosives Tracing Center export rehearsal; DOT HMIS + carrier HazMat wiring; DCSA / ATF / DOT / ITAR / NATO AASTP-1 audit rehearsal.
- Month 4+
Enterprise rollout; SAAS-MOD / TAMIS-R / GCSS-Army / MHP / LIW / OIS-MC / CAS / ROLMS-I full-production feed; ITAR DTrade + CHIEF / ACE customs export; NATO AASTP-1 / STANAG 2493 coalition export; SAAMI manufacturer ERP + commercial DC cutover; RCRA 40 CFR §266.202 military-munitions-rule disposition + DoDM 4160.28 demilitarization export; NTAG424 DNA SUN CMAC AES-128 signatures enabled for ITAR USML Cat. III + ATF Part 555 + NATO Tier-1 lots.
- Pattern begins with a SAAS-MOD / TAMIS-R / MHP / OIS-MC / CAS / ROLMS-I extract + MIL-STD-1168D DODIC / NALC / LOT table reconciliation + DoDAAC consignor / consignee map + UN hazard-class + compatibility-group inventory. GS1 GIAI-96 issuer-code registration under GS1 TDS 2.0 happens before any tag is cut. Encoding facility designation sits off the explosive line per DoD 4145.26-M + DESR 6055.09.
- SKU selection balances container family (PA70 / M2A1 / M2A2 / M19A1 / PA108 / PA120 / 40 mm wooden crate / 155 mm pallet / SAAMI case) and threat profile (depot storage / deployed ASP / vehicle-mounted load / coalition transfer / commercial distribution). MIL-STD-810H Method 514 Procedure I + Annex C profile is validated on the pilot lot. Class II Div 1-2 reader stack is designed for propellant-dust atmospheres per NFPA 495 + NFPA 484.
- Pilot depot: one ASP + one MMAC / MCAAP production line + one contractor bonded-warehouse + one SAAMI-aligned commercial distributor runs the full MIL-STD-129R / 1168D / §173.62-aware programme. The pilot runs under yard portal + dock-door portal + handheld for 90 days in parallel with stencil / paper. DCSA ammunition-safety / ATF compliance / DOT HMIS / ITAR registration / NATO AASTP-1 audit rehearsal validates the event export and bound-record generation.
- Enterprise rollout: SAAS-MOD / TAMIS-R / GCSS-Army / MHP / LIW / OIS-MC / CAS / ROLMS-I feed activation. DoD IUID Registry sync via PIEE / iRAPT. ATF eForm + Explosives Tracing Center wiring. DOT HMIS + carrier HazMat feeds activated. ITAR DTrade + CHIEF / ACE customs export activated. NATO AASTP-1 / STANAG 2493 export for coalition interoperability. SAAMI manufacturer ERPs + commercial DC activation. RCRA 40 CFR §266.202 military-munitions-rule disposition and DoDM 4160.28 demilitarization export activated.
Useful next pages
Use these linked product, guide and comparison pages to keep the next click specific and practical.
Related defense & hazardous-material RFID programmes
Adjacent Proud Tek RFID programmes aligned to MIL-STD / DOT / ATF / ITAR / NATO / SAAMI / NFPA regimes.
Chip-level technical reference
Deep-dive specifications and chip-family comparisons relevant to this SKU.
Industry applications
Industry deep-dives where this SKU is commonly specified.
FAQ
Is the tag compatible with ammunition / propellant-adjacent storage and encoding?
Yes. The tag is passive (no battery, no emissions) and encoded in a bonded facility off the explosive line per DoD 4145.26-M contractor's safety manual and DESR 6055.09 DoD explosives-safety standards. The reader stack for propellant-dust atmospheres uses ATEX / IECEx Zone 21 / 22 + UL / CSA Class I Div 2 / Class II Div 1-2 ratings per NFPA 495 / NFPA 400 / NFPA 484. Because the passive tag emits no RF energy itself, it poses no hazardous-materials compatibility risk to the contained Class 1 munitions.
How does the programme encode MIL-STD-129R + MIL-STD-1168D DODIC / NALC / LOT?
The full MIL-STD-129R §5 military shipping label vector is encoded in a GS1 GIAI-96 carrier per GS1 TDS 2.0 §7.1. That vector spans DODIC (4-character munition code), NALC (2-character interim), LOT serial, DoDAAC consignor / consignee, UN hazard class / division (1.1-1.6), compatibility group (A-S) per DOT 49 CFR §173.52, NEW per §172.202, manufacturer CAGE, and date of pack per DoD 5160.65-M. EPCIS 2.0 events feed SAAS-MOD / TAMIS-R / GCSS-Army / MHP / OIS-MC / CAS / ROLMS-I and the DoD IUID Registry via PIEE / iRAPT.
Does it handle ATF 27 CFR Part 555 explosive-materials and ITAR export-controlled lots?
Yes. The tag auto-generates the ATF 27 CFR §555.127 records of transactions and §555.109 marking verification for every transfer; the export feed pushes to ATF eForm 6 / Explosives Tracing Center on demand. ITAR 22 CFR 120-130 USML Category III lots use the NTAG424 DNA SUN CMAC AES-128 variant for per-scan cryptographic signing (per NXP AN12196), and the key-management pack supports ITAR registration audits, DCSA physical-security inspection, and NATO STANAG 2493 / STANAG 4439 coalition-transfer documentation.
Will the tag survive MIL-STD-810H transport and CARC-paint recoating?
Yes. The housing is polycarbonate / polyurethane / ABS overmold with MIL-DTL-24203 CARC-paint-compatible surface; the tag passes MIL-STD-810H Method 501 / 502 (-40 °C to +85 °C), Method 514 vibration including Procedure I vehicle-transport + Annex C ballistic-transport profile, Method 516 shock (40g / 11 ms half-sine), Method 509 salt fog (96 h), Method 510 sand/dust, Method 507 humidity (10 cycles); and MIL-STD-810H Method 520 combined environments. ASTM B117 1,000 h for naval storage is validated. Read performance is preserved after CARC recoating.
Sources & references
Primary standards, OEM datasheets and regulatory documents cited by this article. All URLs were verified on the access date shown below.
- MIL-STD-129R Marking for Shipment and Storage
Defines the military shipping-label vector encoded on the GIAI-96 carrier for every ammunition container.
- MIL-STD-1168D DODIC / NALC / LOT Ammunition Marking
Defines the DODIC / NALC / LOT identifier structure encoded in the GIAI-96 GS1 carrier.
- DoD 5160.65-M Single Manager for Conventional Ammunition
- DoD 4145.26-M Contractor's Safety Manual for Ammunition and Explosives + DESR 6055.09 Edition 1 DoD Explosives Safety Standards
Explosives-safety and compatibility rules governing tag encoding off the explosive line.
- DOT 49 CFR §172.202 + §173.52 + §173.62 Class 1 Explosives Shipping Description / Compatibility Groups / Table of Hazardous Materials
HazMat transport shipping description, UN hazard / division, compatibility group, and NEW encoded on the tag.
- ATF 27 CFR Part 555 Commerce in Explosives (§555.109 marking + §555.127 records of transactions)
Federal commerce-in-explosives marking and records obligations the EPCIS feed auto-generates.
- ITAR 22 CFR 120-130 International Traffic in Arms Regulations — USML Category III Ammunition / Ordnance
Export-controlled USML Category III lots require NTAG424 DNA per-scan signatures and DCSA-grade custody records.
- NATO STANAG 2493 Ammunition Marking + STANAG 4439 Insensitive Munitions + AASTP-1 Allied Ammunition Storage & Transport Publication
NATO coalition ammunition marking, insensitive-munitions, storage and transport standards.
- SAAMI Z299.1 / Z299.2 / Z299.3 / Z299.4 / Z299.5 Voluntary Industry Performance Standards for Sporting Ammunition
Commercial sporting-ammunition packaging and marking alignment for SAAMI manufacturer / distributor lots.
- MIL-STD-810H + GS1 TDS 2.0 + EPCIS 2.0 + NXP AN12196 NTAG424 DNA SUN CMAC AES-128
Environmental qualification basis, GIAI-96 carrier schema, event model, and NTAG424 DNA per-scan signature mechanism.
Proud Tek is a Shenzhen-based RFID & NFC manufacturer supplying hotel chains, transit operators, event venues and retail brands worldwide. Every order includes free samples, RF testing and dedicated project support.
Get a Quick Quote
Tell us about your project and we'll respond within one business day. Fields marked (asterisk) are required.